540
spacer
Podcasts
spacer
Night School
spacer
steelTOOLS
spacer

AISC Offers Advice on Recent HSS Issues

December 13, 2007 From American Institute of Steel Construction, Inc.

Material Properties and Documentation
Questions first arose a few months ago about the mechanical properties of imported HSS, as well as the credibility and reliability of the documentation provided when the imported products entered the U.S. and Canada. At that time, AISC advised that it was premature to draw any conclusions until information could be assembled and independently reviewed.

Since then, we have collected the available data, which represents a limited number of tests on mechanical and chemical properties. AISC staff and industry materials consultants have reviewed this data and noted the following:

  • Many of the tests were performed to different procedures and protocols than are required for HSS in ASTM A500, and therefore lacked uniformity for analysis;
  • Testing speeds varied significantly among the tests that were reported to us; and
  • There was no control or tracking of the location of test specimens as to what position they came from in the width and length of the coil.

Despite these factors, each of which will induce significant variations in the testing results, the mean of the independent test results was similar to the mean of the Material Test Report values. As should be expected, these factors did result in a higher standard of deviation. Accordingly, it is AISCs conclusion that this does not represent a building code issue.

“Perhaps the most important recommendation is that the buyer should know and evaluate their material supply chain,” stated Roger Ferch, P.E., AISCs president. “As with any other purchase, don’t just look at the quoted price but also consider the quality, reputation, and experience of the supplier.” Also, it is important to verify that the material and its documentation meet ASTM A500 requirements when it is received. A few Material Test Reports AISC received with the information submitted to us were for material that had been accepted by the purchaser with metric values reported on the MTRs that did not meet the minimum ASTM requirements. Such deviations can be avoided with simple receiving inspection of the material to ensure it is as it was ordered.

Seam Weld Quality
In addition, AISC has received reports of seam weld quality concerns with imported HSS. The seam weld deficiencies that led to these concerns can be seen on the California Division of the State Architect website (www.dsa.dgs.ca.gov/labs/hss_pictures.htm) based upon their discovery of weld seam problems in some imported HSS. As can be seen in the photographs, the defective material is such that the defects are identifiable through visual inspection.

The limited information that is available to date on this topic and the anecdotal nature of reports of weld seam defects leads us to believe there is no crisis in HSS supply and no dramatic response is necessary. “Producer quality control is an essential part of the supply chain and we believe that North American producers are routinely exercising good QC processes,” explained Louis F. Geschwindner, vice president of engineering and research at AISC. “Receiving inspection at various levels is a routine method to evaluate supplier quality control, and we believe that steel service centers and fabricators are properly performing this function. Where a supplier is new or unknown, these reports may be cause to increase vigilance to ensure that the material they supply is acceptable.”

AISC will continue to monitor these situations and keep the design community and construction industry informed of any changes. If additional information is needed, please contact AISCs chief structural engineer, Charles Carter, P.E., S.E., at [email protected] or contact the AISC Steel Solutions Center at [email protected].

For more information contact:

Scott Melnick
VP of Communications
(312) 670-8314
[email protected]

American Institute of Steel Construction
The American Institute of Steel Construction, headquartered in Chicago, is a not-for-profit technical institute and trade association established in 1921 to serve the structural steel design community and construction industry. AISC’s mission is to make structural steel the material of choice by being the leader in structural steel-related technical and market-building activities, including: specification and code development, research, education, technical assistance, quality certification, standardization, and market development. AISC has a long tradition of service to the steel construction industry of providing timely and reliable information. 

130 East Randolph Dr. Suite 2000
Chicago IL 60601
Phone: (312) 670-2400
Fax: (312) 896-9022
www.aisc.org